SCB13-27.5kV series dry-type three-phase power transformer

Epoxy cast non excited pressure regulating dry transformer is made of F-grade epoxy resin mixture with fillers. After vacuum film degassing, high and low voltage coils reinforced with glass fiber forming mesh are placed on the inner and outer surfaces of the thin layer casting under vacuum and pressure.
View more

S13-27.5kV series oil immersed three-phase power transformer

The S13 series 27.5kV no-load tap changer power transformer is an energy-saving distribution transformer designed and produced by our company, widely used in railways, large and medium-sized industrial and mining enterprises, and 27.5kV substations. The product has the characteristics of reasonable structural design, high operational reliability, significant energy-saving effect, strong overload capacity, and low noise. Compared with products produced according to current national standards, the average no-load loss has decreased by 20-30%, and the no-load current has decreased by 50-60%. Reaching the advanced level of similar international products.
View more

TES series oil immersed (dry-type) inverse Scott transformer

The reverse Scott transformer is a special type of transformer that can convert the two-phase electricity (two single-phase with a phase difference of 90 °) of the power supply (referred to as the road network) into three-phase electricity, that is, the traction equipment side (referred to as the station side).
View more

SCZ13-35kV series dry-type three-phase on load tap changer transformer

The epoxy resin cast dry-type on load tap changer is equipped with a dry-type on load vacuum tap changer and an intelligent controller (hereinafter referred to as YJK-1). The intelligent controller is mainly used to control the dry-type on load vacuum tap changer, and the switching operation of the on load tap changer is controlled by the electric operating mechanism inside the on load tap changer to achieve the purpose of voltage regulation.
View more

SCB13-35kV series dry-type three-phase power transformer

Epoxy cast non excited pressure regulating dry transformer is made of F-grade epoxy resin mixture with fillers. After vacuum film degassing, high and low voltage coils reinforced with glass fiber forming mesh are placed on the inner and outer surfaces of the thin layer casting under vacuum and pressure. It is a dry-type transformer with high mechanical strength, electrical strength, heat resistance, low loss, low noise, strong heat dissipation ability, and equipped with a complete temperature protection control system. It is an excellent product for urban power grid renovation, widely used in important places such as power, railway (road), energy, chemical, high-rise buildings, airports, power stations, commercial centers, etc. that require fire prevention, explosion prevention, and moisture prevention.
View more

SZ13-35kV series oil immersed three-phase on load regulating power transformer

The on load tap changer power transformer is an energy-saving distribution transformer designed and produced by our company. The product has the characteristics of reasonable structural design, high operational reliability, significant energy-saving effect, strong overload capacity, and low noise.
View more

S13-35kV series oil immersed three-phase power transformer

The S13 series 35kV non excited voltage regulating distribution transformer is an energy-saving distribution transformer designed and produced by our company. It is widely used as a station transformer in large and medium-sized industrial and mining enterprises and 35kV substations. It has the characteristics of reasonable product structure design, high operational reliability, obvious energy-saving effect, strong overload capacity, and low noise. Compared to products produced according to current national standards. The average empty loss has decreased by 20-30%, and the no-load current has decreased by 50-60%, reaching the advanced level of similar international products.
View more

DC13 series 10kV, 27.5kV single-phase resin insulated dry-type power transformer

The insulation system of single-phase epoxy resin cast dry-type transformer is based on epoxy resin insulation material, and has the advantages of simple structure, small volume, good energy-saving effect, strong overload capacity, high mechanical strength, small partial discharge, high reliability, long operating life, flame retardant, pollution-free, lightweight, automatic temperature control, etc. It can be widely used in power transmission and transformation systems, railway (public) roads, rural power grids, and commercial loads, and is also suitable for other light industries and commercial lighting.
View more

SC (B) H15/17/19-10kV series dry-type three-phase amorphous alloy power transformer

The amorphous alloy resin cast dry-type transformer adopts a new generation of iron core material, amorphous alloy. The most significant feature of amorphous alloy is low unit loss. Under the same magnetic density, the unit loss of amorphous alloy iron core is only 25% of cold-rolled silicon steel sheet, and the energy-saving effect is very significant. The amorphous alloy resin cast dry-type transformer inherits all the advantages of epoxy resin cast dry-type transformers and is a key recommended product for urban power grid renovation. It can be widely used in places with high protection requirements such as power, railway (public), energy, chemical, high-rise buildings, commercial centers, subways, airports, stations, industrial and mining enterprises, and power plants.
View more

SZ11/13 series 10kV, 35kV three-phase on load regulating transformers

The on load tap changer power transformer is an energy-saving distribution transformer designed and produced by our company. The product has the characteristics of reasonable structural design, high operational reliability, significant energy-saving effect, strong overload capacity, and low noise.
View more
< 1234 >